AnatomyOfABullet < Gunwiki

<!--
   * Set TOPICTITLE = Anatomy of a Bullet
-->
---+ The Anatomy of a Bullet

<img align="right" src="%ATTACHURLPATH%/RoundDiagram.png" alt="RoundDiagram.png" width='300' height='266' />
This would have been, more correctly, referred to as 'The Anatomy of a Round'.  However, 'bullet' seems to flow better, so I hope you'll permit me this one bit of artistic license in the article's title.

A loaded round is a balance of four components:
   * A bullet
   * The case (usually brass, but it's _called_ brass, even if it's made of aluminum or steel, or even nickel-plated brass)
   * Powder (there are many types, with a variety of burn rates and 'cleanness')
   * Primer (the cap in the bottom, which ignites the powder)

If what you're actually looking for is how to tell what a bullet is from its abbreviation (FMJ, etc), then you should check out the [[RefProjectileAbbreviations][projectile abbreviations]] guide.
<br clear=all>
---++ 'Grains' In Ammunition
A grain is 1/7000th of a pound.  This is how both powder and bullets are weighed.  Usually, when you see a box of ammunition, it will state the weight of the bullets in grains.  However, the powder charge is usually not listed.  While the metric system would be equally well suited to expressing the weights of charges and projectiles, the Imperial system is the one most commonly used in reloading components.  Projectiles, for instance, are usually sold by caliber and not millimeter.

---+++ Bullets
As mentioned above, bullets are weighed by the grain.  A bullet which weighs 55 grains (typical for 223 caliber) weighs .0078571428 pounds.  The sheer number of decimal points should make it obvious why bullet weights are expressed in grains, and not in fractions of a pound.  Furthermore, the firearms industry isn't likely to switch to the metric system for weights at any point.  To add further confusion, bullets are frequently listed by caliber only, for rounds which are commonly expressed in millimeters.  For example, the 7.62x39mm cartridge uses a .311 caliber bullet.  It is expected that if you get set up to reload a caliber, you will learn the appropriate caliber designation for the bullets you're using.
You will find documentation on the various bullet abbreviations [[RefProjectileAbbreviations][here]].  One thing to be aware of in bullet design, is that a cannelure is the small grooved ring around a bullet, which indicates how deeply it should be seated in the case. Without a cannelure, you have to rely on neck tension to hold the bullet, and have no way to visually identify a bullet that's seated too far forward.

---+++ Powder
There are many types, with a variety of burn rates and residue.  Like bullets, powder is measured in grains, of which there are 7000 in a pound.  Powder is typically sold by the pound.

---+++ Primers
Of these various elements, the primer is the least variable.  There are only four _common_ sizes of primer - large rifle, small rifle, large pistol, and small pistol.  Less common sizes are 50 BMG, and a plethora of Berdan sizes which very few folks ever reload with.  Primers are generally inexpensive; a box of 5000 can be had for around 2 cents a primer.  The main variation between primers of a certain size, is how 'hard' or 'soft' they are.  Extremely soft primers are easy to detonate; hard primers require more force.  It is possible to load soft primers into rifle rounds in order to result in fully automatic fire, but only a complete idiot would do this in any conventional firearm design.  If you've been looking for a way to remove a hand or a few fingers, this can be an effective way to do it when your gun explodes due to an out-of-battery discharge.

---++ Caliber vs Millimeter
These are two different means of measuring the diameter of a bullet.  A caliber is generally a fraction of an inch, while millimeters are, well millimeters.  While these may seem to be precise numbers (7.62x39mm, for example), most of them actually aren't.  7.62x39mm rounds use .311 caliber bullets, whereas 7.62x51mm rounds use .308 caliber bullets.

---++ Understanding Bullet Weights
When buying ammunition, it's not uncommon to see "180gr hollow-point" ammunition right next to "230gr full metal jacket" ammunition, both in 45ACP.  The "180gr", etc, is the weight of the actual _projectile_ in grains.  The projectile is the bullet only, not the rest of the case.  To weigh one, you would have to remove it from the loaded round and put it onto a scale sensitive enough to provide its weight.  Because this is not a readily performed procedure for the average guy who just bought his gun, you should simply trust that, for factory-new ammunition, the weight of a bullet is the same as what it says it is.  There are a variety of reasons for these different weights, and it is not necessarily power.  A heavier bullet _will_ have more material, but assuming the same pressure propelling it, it will have a slower velocity and will start to drift downward faster than a lighter bullet.  A lighter bullet will be be more affected by wind or objects than a heavier one, unless of course it happens to have an unconventional (armor piercing, for instance) core.  One example of lighter vs heavier bullets, is that when 223 rounds pass through leaves, their accuracy is hugely impacted.  When a 308 round, which is a much larger bullet with more kinetic energy behind it, passes through a leaf, it does suffer a little but nowhere near as much as the 223.

---++ What you need to know about corrosive ammo
Corrosive ammunition is not, in and of itself, corrosive.  What causes corrosion are various salts which are deposited by the primer (and in some cases, the powder) in the places where carbon buildup normally occurs.  These salts absorb moisture from the air, and the moisture causes rust.  Yugoslavian rifles, due to most of them lacking chrome lined barrels, are particularly likely to develop rust issues from corrosive ammunition.  However, the salts are not restricted to the barrel alone, and may also infest the gas system and FCG area.  Salt can be dissolved and flushed out by washing out the rifle with ammonia, windex, or warm soapy water, and then drying it out immediately.

---++ Digging Deeper
If you want to learn more about what makes a loaded round tick, you will probably want to read the [[RefReloadingIntro][Introduction to Reloading]] article.

-- Main.SeanNewton - 12 Aug 2006
Attachments
Topic attachments
I	Attachment	History	Action	Size	Date	Who	Comment
png	RoundDiagram.png	r2 r1	manage	14.8 K	04 Jul 2008 - 02:08	UnknownUser
This topic: Gunwiki > WebHome > AnatomyOfABullet
Topic revision: r17 - 10 Mar 2009 - SeanNewton